引燈鏡頭應用：深圳工業燈鏡投影機：投影機主要由凸透鏡成像制成，可以放大，倒立實體圖像原理。在投影中，從投影膜到凸透鏡成像的距離保持在焦距的12倍之間，然后借助平面鏡更改光的折射定律方位。凸透鏡成像越靠近投影膜，圖像越大，反向越小。投影時，首先將投影膜放在載波表上，然后調整投影膜到凸透鏡成像的距離，并注意調整平面鏡的角度，使圖像在螢幕中間。放大鏡：在1f中，物體處于正位置，放大正位置的虛擬影像，放大正位置的虛擬影像，放大虛擬影像。使圖像更大，使物體遠離鏡頭（接近1f）。如果你想要帶放大鏡的指紋，如果你想要一個指紋來回答，當你不動的時候，把放大鏡從手指上移開。手指接近1f。
集成化控制模組鏡片的結構分析對于高端鏡片來說是非常重要的，但如何將一個好的光學設計轉換成一個商品則是最重要的。然而，鏡片（特別是高端光學鏡片）是如何制作、組裝和檢測的？本文以中倍鏡為例，簡要介紹了該鏡片的電子光學冷拉、結構設計和裝配工藝。
很多沒有電子光學冷拉生產車間的好朋友對集成化控制模組鏡片的生產加工技術性都很好奇，事實上，電子光學冷拉就是分割、精拋、精拋、打磨拋光、邊磨、鍍層、膠水粘等。具體的電子光學冷拉技術性在這里并不詳細，這里是國內光學鏡頭一般加工精度的重點。以便保持商品的品質，大家必須對商品開展檢測，對光電材料商品的外觀檢測列出一些相關問題。點缺陷：由于點形缺陷，檢測人員應以最大直徑測量其尺寸。如顏色點的出現、氣泡、凹坑、油漬等不良現象。毛邊：由于精密模具預成型零件參數或模具，會使商品的邊沿或分型面產生廢緣。粗糙邊沿主要是胚胎擠壓后磨削不均造成的。硬刮痕：由于硬材料磨損，商品表面有深刻的刮痕。大多數都是機械的。劃痕：沒有深刻劃痕。一般在分揀中，包裝過程不符合標準操作，追蹤不易找到。
Applications of Projection Lenses: Shenzhen Industrial Projection Lamps
Projection lamps primarily use convex lenses to create magnified and inverted real images.
Projection Principle
? The distance between the projection film and the convex lens must remain within 1 to 2 times the focal length.
? Plane mirrors are used to adjust the light’s direction according to the law of refraction.
? The closer the convex lens is to the projection film, the larger the image becomes, and the inversion effect decreases.
Steps for Projection
1. Place the projection film on the carrier table.
2. Adjust the distance between the film and the convex lens.
3. Modify the angle of the plane mirror to ensure the image appears centered on the screen.
________________________________________
Magnifying Glass Applications
? At a distance of 1f, the object is in an upright position, and the magnifying glass produces a virtual, upright, and magnified image.
? Moving the object closer to the lens (near 1f) enlarges the image.
Example:
To examine a fingerprint using a magnifying glass:
? Adjust the lens’s distance from the fingerprint for a clear image.
? To enlarge further, move the lens closer to 1f and the object.
________________________________________
Structural Analysis of Integrated Control Module Lenses
High-end lenses require converting optical designs into practical products through meticulous manufacturing and assembly processes.
Example: Medium Magnification Lens
The production process includes:
? Optical Cold Drawing techniques such as:
o Cutting
o Precision grinding
o Fine polishing
o Edge grinding
o Coating application
o Adhesive bonding
Although details of optical cold drawing processes are not fully described, this method is crucial for achieving precision in lens manufacturing.
________________________________________
Quality Inspection for Optoelectronic Materials
To maintain product quality, optical materials undergo appearance inspections.
Common Defects:
1. Point Defects:
o Inspectors measure the maximum diameter of defects like color spots, bubbles, pits, or oil stains.
2. Burrs:
o Caused by pre-molding parameters or mold issues, resulting in waste edges at the product’s perimeter or parting line.
o Rough edges are often caused by uneven grinding after preform extrusion.
3. Hard Scratches:
o Deep scratches caused by abrasion from hard materials, typically during mechanical processing.
4. Surface Scratches:
o Shallow, superficial scratches often occur during non-standard sorting or packaging processes, making them harder to trace.
By addressing these issues during manufacturing and inspection, optical lenses achieve the precision and quality necessary for advanced applications.
